Description

MTRX-03X16-Gis a high performance, cost effective modules, which is optimized for 10G SONET/SDH Ethernet and WAN applications, supporting data-rate of 10.3125Gbps (10GBASE-ER) or 9.953Gbps (10GBASE-EW), and transmission distance up to 40km .

The transceiver consists of two sections: The transmitter section incorporates a 1550nm cooled EML, driver and re-timer. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA) and CDR. The module is hot pluggable into the 30-pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module. The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver.

A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire XFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.

Features

lSupport 10GE application at the data-rate of 10.3125Gbps and 9.953Gbps

lUp to 4 0km transmission

l1550nm cooledEML and PIN receiver

lXFI electrical interface

l2-wire interface for integrated Digital Diagnostic monitoring

lXFP MSA package with duplex LC connector

lHot pluggable

lVery low EMI and excellent ESD protection

l+3.3V&+5V power supply

lPower consumption less than3.5 W

lOperating Case Temprature:0~+ 70 ℃

Application

lSONET(OC-192)/SDH(STM64) line card

l10GBASE-ER at 10.3125Gbps

l10GBASE-EW at 9.953Gbps

lOther optical links

Standard

lCompliant with XFP MSA

lCompliant with IEEE 802.3ae-2002

lRoHS compliance

Specification

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit
Storage Temperature	TS	-40	+85	℃
Supply Voltage #3	VCC3	-0.5	3.6	V
Supply Voltage #5	VCC5	-0.5	6.0	V
Relative Humidity	RH	-	+85	%
RX Input Average Power	Pmax	-	5	dBm

Recommended Operating Conditions
Parameter	Symbol	Min.	Typical	Max.	Unit
Operating Case Temperature	TC	0	-	+70	℃
Power Supply Voltage #3	VCC3	3.13	3.3	3.45	V
Power Supply Current #3	ICC3	-	-	750	mA
Power Supply Voltage #5	VCC5	4.75	5	5.25	V
Power Supply Current #5	ICC5	-	-	300	mA
Total Power Dissipation	PD	-	-	3.5	W
Data Rate		9.95	-	11.3	Gbps
Transmission Distance		-	40	-	Km

Transmitter Operating Characteristic-Optical
Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Centre Wavelength	λC	1530	1550	1565	nm	Note1
Side Mode Suppression Ratio	SMSR	30	-	-	dB
Laser Off Power	Poff	-	-	-30	dBm
Average Optical Power	Pavg	-3	-	3	dBm	Note1
Extinction Ratio	ER	8.2	9	-	dB
Transmitter Dispersion Penalty	TDP	-2.1	-	-	dBm
Relative Intensity Noise	Rin	-	-	-128	dB/Hz
Operating Data Rate		9.95	-	11.3	Gbps
Optical Eye Mask	Compliant with IEEE 802.3ae					Note2

Notes:

[1] Average optical power shall be measured using the methods specified in TIA/EIA-455-95.

[2] Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver.

Notes:

[1] Receiver sensitivity is informative. Stressed receiver sensitivity shall be measured with conformance test signal for BER =1x 10^-12.

[2] Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver.

Notes:

[1] Pull-up resistor must be connected to host_Vcc on the host board. Iol(max)=3mA

[2] Pull-up resistor must be connected to host_Vcc on the host board.

[3] Pull-up resistor connected to VCC3 within XFP module. Iil(max)= -10μA.

[4] Pull-up resistor connected to VCC3 within XFP module. Iih(max)= 10μA.

[5] Pull-up resistor must be connected to host_Vcc on the host board. Iol(max)= -10μA.

[6] Pull-up resistor must be connected to host_Vcc on the host board. Iol(max)= 10μA.

[7] At 400KHz, 3.0kohms, at 100kHz 8.0kohms max.

[8] At 400KHz, 0.8kohms, at 100kHz 2.0kohms max.